Skip to content
By 4 min read

How to Make a 3D Printed Cookie Cutter From Your Own Measurements

Cover picture for How to Make a 3D Printed Cookie Cutter From Your Own Measurements

You have a favorite cookie cutter that is cracked, or you want a shape that no store sells. A 3D printer can make the cutter for you, sized to the exact shape you need.

The trick is the wall. A cookie cutter needs a thin, sharp edge to cut through dough, and a flat top that you can press on. In this guide, you will design a cutter frame, check its size, and print it in pieces if it is too big for your build plate.

What a good cookie cutter needs

A printed cutter is a frame of thin walls. Use these numbers as a starting point, with a 0.4 mm nozzle:

  • Cutting wall: about 1.2 mm thick, with a height of 14 to 20 mm
  • Top lip: a flat edge 2 to 4 mm wide on the top, so you can press down evenly
  • Scoring walls: inside the cutter, a few millimeters shorter than the cutting wall, so you can score the dough without cutting all the way through

The cutting wall needs to be taller than the dough is thick. The scoring walls let you mark details, such as a face or a line of frosting, without slicing through.

Measure the shape you want

Start with a clear measurement. Trace the shape on paper, or use a shape you already have. Measure the widest point in width and height, then write the numbers down.

Use the outside size of the cutter, not the inside. The outside size is what you will type into the studio.

Design the frame in ShapeNook

Open ShapeNook in the studio. Set the outside width and height with exact numbers.

To build the cutting wall, use this method. It works best for simple shapes, such as rectangles, circles and other simple outlines.

  1. Make a solid shape at the outside size of the cutter.
  2. Put a hole shape inside it that is 2.4 mm smaller than the outside size, which is 1.2 mm per side.
  3. The wall between the two shapes comes out exactly 1.2 mm thick.
  4. Add the top lip along the top edge.
  5. For scoring walls that sit inside the outline, use thin boxes 1.2 mm wide, a few millimeters shorter than the cutting wall.

Check that the walls are the same thickness all the way around. Uneven walls cut unevenly.

Split it if it is bigger than the build plate

Many cutters are bigger than a printer's build plate. If your cutter does not fit, split it into pieces that fit, print each piece, and glue them together.

Here is a real example. An 11 by 10.5 inch cutter with 8 sections is too big for a 256 mm plate. It prints as 4 quarters, each about 5 5/8 by 5 3/8 inches, which fits on the plate.

The walls where the quarters meet are doubled, so the pieces glue together face to face.

When you split a design, check the math. The section sizes plus the walls where they meet should add up to the outside size. If they do not, the finished cutter will be too big or too small.

Export the file and print it

Export the file and print it. Print the cutter with the cutting edge facing up. The lip sits flat on the plate, and the thin walls rise up to the cutting edge.

Slice the model and check the preview before you start. Look for thin walls that did not print, and check the top lip for gaps.

Glue the pieces

For a split cutter, glue the quarters face to face along the doubled walls. Dry-fit the pieces first, and check that the outside edge is straight before the glue sets. Sand the joints lightly so the cutting edge stays smooth.

Use and clean it safely

Use PLA for this cutter, and use it for dough, not for long contact with food. Keep these simple rules in mind:

  • Hand wash the cutter in warm water with mild soap.
  • Dry it fully before you store it.
  • Do not leave it in contact with wet food for long periods.
  • Replace it if the walls crack or warp.

Do not put a printed cutter in the dishwasher or the oven.

Test before you bake

Press the cutter into a small piece of dough before you cut the whole batch. Check the edges, the scoring and the top lip. If the cutter is hard to press through, make the cutting wall a little thinner or the top lip a little wider, then print again.

Share the design

Once your cutter works, you can save the design and print another copy for a friend. Make a note of the size and the number of pieces, so the next print is quick.

For help with fit and print checks, read the guide to printing parts that fit.

Start your own cutter

Measure a shape you love, set the walls, and print one test piece. You will learn more from one test cutter than from any guide.

Start in the studio and design your first cutter.

What will you make first?

Try it in ShapeNook

Design it yourself with exact sizes, fit tests and print checks, free in your browser. Then export the file for your own printer.

Start designing free
Ask Nook